Inhaltsverzeichnis
Letzte Änderung: 29.04.2024 (Video added)
HiCAD 2023
Erste Schritte im Fassadenbau Teil 1
HiCAD 2023
Erste Schritte im Fassadenbau Teil 2
HiCAD 2023
Erste Schritte im Fassadenbau Teil 3
Erste Schritte im Fassadenbau Teil 4
HiCAD 2023
HiCAD 2023
Erste Schritte im Fassadenbau Teil 5
HiCAD 2023
Erste Schritte im Stahlbau Teil 1
HiCAD 2023
Erste Schritte im Stahlbau Teil 2
HiCAD 2023
Erste Schritte im Stahlbau Teil 3
HiCAD 2021 SP1
Create facade section
In this video you can see very nicely how you can create a facade connection very quickly
HiCAD 2020
Modeling a stair tower
In this longer video I show you how to model a stair tower right from the start. I also go into a wide variety of topics and show numerous tips and tricks
HiCAD 2020
Modeling a balcony with a railing
Here in this video I show how you can model a railing on a balcony slab.
HiCAD 2020
How do I model a canopy?
In this video I show how I model a canopy.
HICAD 2021
Model the facade connection
In this video I show you how to draw a facade connection. There will be a new video on this topic soon, as there have been a lot of further developments in this area lately, which I would like to show you of course.
These further developments increase the speed many times over.
HICAD 2021
How do I parameterize a facade connection
Here in this video I show how to parametrically set up a facade connection in order to use it again and again for further projects.
HICAD 2021
How can I draw a garbage dump canopy
In this video you can see how I draw a garbage dump
HICAD 2021
How can you develop and manage curved Alucobond sheets
In this video I show an approach how to manage curved Alucobond sheet metal cassettes and prepare them for automatic output.
Basically, a curved sheet metal cassette cannot be modeled because the side tabs cannot be modeled for it. However, since this is done to a certain extent in practice, I would like to show a little way how you can manage this anyway.
The basic idea is that you work with 2 parts which are controlled together via an assembly. The first sheet represents the actual representation for the details and drawings. The more time you invest in the representation of the 3D part, the better the representation looks. From this, however, the development is also calculated manually in order to take over for the 2 part that represents the straight part in order to generate the development from it.
That's why exactly the 2nd part is necessary. This is only generated to create a development from it. This is why the length of the curved flap is added to this part.
I used the external referencing to not have to make the workshop drawing of the sheets for each part, but so that most things are preserved and I only have to correct any shifted dimensions.
Unfortunately, there is no sound in the video because my microphone was defective in this video.
HiCAD 2022 | Railing infill
How do I store a filling in the configurator
In this video I show how you can store a filling for the configurator and also expand it.
HiCAD 2022 | Geländerpfosten
Wie hinterlege ich einen Pfosten in den Konfigurator
In diesem Bild sehen sie welche Variablen man benötigt um den Pfosten zu definieren.
Wichtiger Hinweis zu Pfosten:
Beim Pfosteneinbau sind die 1/2 Pfostendicke in x- bzw. y-Richtung keine Eingabewerte des Geländerkonfigurators (i_ex…, i_ey…), sondern die Werte müssen von der Pfostenvariante erzeugt werden. Deshalb dürfen in der Variante nicht die Variablen i_ex und i_ey verwendet werden, sondern stattdessen ex und ey. Diese Werte stellt der Geländerkonfigurator dann in den Variablen i_ex bzw. i_ey der Füllung zur Verfügung.
HiCAD 2022 | Arbeitsweise Schlosserei
Typische Arbeitsweise einer Schlosserei mit einer Punktewolke
In diesem Video zeige ich wie man eine Punktwolke in HiCAD einliest, in dieser eine Geländer und Handlauf an die Wand montiert sowie eine kleine Überdachung.